cars01010
09-19-2008, 12:30 AM
© Copyright 2006, DaimlerChrysler Corporation, All Rights Reserved
August 2006
Distributor/Dealer Service Instructions for:
Safety Recall F33 – Directional Signal Bulb
Function
2005 (LX) 300/Magnum (International Markets)
2006 (LE) 300/Magnum/Charger (International Markets)
2006 (PT) PT Cruiser (International Markets)
NOTE: This information applies to all LX models, LE (Graz built) models
built through June 22, 2006 (MDH 062208), and PT models built through
January 10, 2006 (MDH 011015) with side repeater lamps (Sales Code LMF).
The driver’s “telltale” for directional signal bulb failure may not provide feedback
to the driver if a problem exists with the signal bulb(s) for vehicles built with side
repeaters.
Models
IMPORTANT: Some of the involved vehicles may be in distributor/dealer
used vehicle inventory. Distributors/Dealers should complete this recall
service on these vehicles before retail delivery. Distributors/Dealers should also
perform this repair on vehicles in for service. Involved vehicles can be determined
by using the VIP inquiry process.
Subject
Safety Recall No. F33 - Directional Signal Bulb Function
The Front Control Module (FCM) on LX/LE models or Totally Integrated Power
Module (TIPM) on PT models must be reprogrammed.
No parts required to perform this service procedure.
The following Special Tools are required to perform this service procedure:
NPN Battery Charger
CH9401 StarSCAN® Tool
CH9404 StarSCAN® Vehicle Cable
CH9409 StarSCAN® Documentation Kit
CH9410 StarSCAN® Ethernet Cable, 3.7 m (12 ft.)
CH9412 StarSCAN® Software Update Device Kit
TechCONNECT PC or equivalent
Reprogram the FCM/TIPM Module
NOTE: Before performing this Repair Procedure, the operating software in
the StarSCAN®must be programmed with software release level 7.01 or
higher. The software release level is visible in the blue header at the top of
the StarSCAN® screen.
CAUTION: Follow the flash reprogramming procedure carefully on LX/LE
models. The FCM does not support abort/recovery. If an error occurs,
the FCM will require replacement.
Repair
Parts Information
Special Tools
Service Procedure
Safety Recall No. F33 - Directional Signal Bulb Function
NOTE: The StarSCAN®diagnostic scan tool fully supports Internet
connectivity. However, to take advantage of this feature you must first
configure the StarSCAN® for your dealership's network. Make sure the
StarSCAN® is configured to the dealership's network before proceeding.
For instruction on setting up your StarSCAN® for the dealer's network
refer to either: “DealerCONNECT > Service > StarSCAN and
StarMOBILE tools > Online Documentation”, or refer to the StarSCAN®
Quick Start Networking Guide. The StarSCAN® Quick Start Networking
Guide is also available on the www.dcctools.com website under the
"Download Center".
1. Install a battery charger and verify that the charging rate provides
approximately 13.2 - 13.8 volts. Set the battery charger to continuous charge.
Do not allow the charger to time out during the flash process. Remove the
charger from the battery when the flash process is complete.
2. Connect the CH9410 StarSCAN® ethernet cable to the StarSCAN® and the
dealer's network drop.
3. Connect the CH9404 StarSCAN® vehicle cable to the StarSCAN® and the
vehicle.
4. Power ON the StarSCAN®.
5. Select "ECU View".
6. Touch the screen to highlight the TIPM/CGW or Front Control/Central
Gateway in the list of modules.
7. Select "More Options".
8. Select "ECU Flash"
9. Record the part number at the top of the "Flash" screen for later reference.
10. Select "Browse for New File". Follow the on screen instructions.
11. Highlight the appropriate calibration then select "Download to Scantool"
12. Select "Close" after the download is complete, and then select "Back".
13. Highlight the listed calibration.
14. Select "Update Controller". Follow the on screen instructions.
15. When the update is complete, select "OK".
Service Procedure cont.
Safety Recall No. F33 - Directional Signal Bulb Function
16. Verify the part number at the top of the "Flash” screen has updated to the
new part number.
NOTE: Due to FCM/TIPM programming, a DTC may be set in other modules
(PCM, TCM, BCM, MIC, SKREEM, etc.) within the vehicle, if so
equipped. Some DTC's may cause the MIL to illuminate. From the
"Home" screen select "System View". Then select "All DTCs". Press
"Clear All Stored DTCs" if there are any DTCs shown on the list.
Claims for vehicles that have been serviced must be submitted on the
DealerCONNECT Claim Entry Screen located on the Service tab. Claims
submitted will be used by DaimlerChrysler to record recall service completions
and provide dealer payments.
Use the following labor operation number and time allowance:
Labor Operation Time
Number Allowance
Reprogram FCM - LX/LE (B) 18-F3-31-82 0.3 hours
Reprogram TIPM - PT (B) 18-F3-31-83 0.3 hours
NOTE: See the Warranty Administration Manual, Recall Claim Processing
Section, for complete recall claim processing instructions.
Regional offices will receive an electronic list of involved vehicles. The Vehicle
List is arranged by Distributor/Dealer code and in Vehicle Identification Number
(VIN) sequence. The lists are for Distributor/Dealer reference in arranging for
service of involved vehicles.
Service Procedure cont.
Completion Reporting and Reimbursement
Distributor/ Dealer Notification and Vehicle List
Safety Recall No. F33 - Directional Signal Bulb Function
All involved vehicle owners should be notified of the service requirement by their
Distributor/Dealer. Owners are requested to schedule appointments for this service.
A sample copy of the owner notification letter is attached.
All involved vehicles have been entered into the Global Recall System (GRS) and
Vehicle Information Plus (VIP) for Distributor/Dealer inquiry as needed.
GRS provides involved Distributors/Dealers with an updated VIN list of their
incomplete vehicles. Completed vehicles are removed from GRS within several
days of repair claim submission.
Distributors/Dealers must perform this repair on all unsold vehicles before
retail delivery. Distributors/Dealers should also use the VIN list to follow up with
all owners to schedule appointments for this repair.
If you have any questions or need assistance in completing this action, please
contact your International Service and Parts Manager.
International Service and Parts
DaimlerChrysler Corporation
Owner Notification and Service Scheduling
Vehicle Lists, Global Recall System, VIP and Distributor/Dealer Follow up
Additional Information
© Copyright 2006, DaimlerChrysler Corporation, All Rights Reserved
SAFETY RECALL - DIRECTIONAL SIGNAL BULB FUNCTION
Dear 300/Charger/Magnum/PT Cruiser Owner:
Customer satisfaction is very important to DaimlerChrysler. Accordingly, we are recommending
the following service on 2005 model 300/Magnum vehicles and some 2006
300/Magnum/Charger/PT Cruiser vehicles.
The problem is...
The driver’s “telltale” for directional signal bulb failure may not
provide feedback to the driver if a problem exists with the signal
bulb(s).
What your dealer
will do...
DaimlerChrysler will repair your vehicle free of charge (parts and
labor). To do this, your dealer will reprogram the Central Gateway
Module with new software. The work will take about ˝ hour to complete.
However, additional time may be necessary depending on how dealer
appointments are scheduled and processed.
What you must do...
If you need help...
Simply contact your dealer right away to schedule a service appointment.
If you have trouble getting your vehicle serviced, please contact the
DaimlerChrysler Distributor nearest your location. A representative will
assist you in getting your vehicle serviced. This information can be found
in the Customer Assistance section of your Owner's Manual.
If you have already experienced the problem described above and have paid to have it repaired,
contact the DaimlerChrysler Distributor nearest your location for reimbursement procedures.
We apologize for any inconvenience, but we are sincerely concerned about your
satisfaction with your DaimlerChrysler vehicle. Thank you for your attention to
this important matter.
International Service & Parts
DaimlerChrysler Corporation
Notification Code F33
August 2006
Distributor/Dealer Service Instructions for:
Safety Recall F33 – Directional Signal Bulb
Function
2005 (LX) 300/Magnum (International Markets)
2006 (LE) 300/Magnum/Charger (International Markets)
2006 (PT) PT Cruiser (International Markets)
NOTE: This information applies to all LX models, LE (Graz built) models
built through June 22, 2006 (MDH 062208), and PT models built through
January 10, 2006 (MDH 011015) with side repeater lamps (Sales Code LMF).
The driver’s “telltale” for directional signal bulb failure may not provide feedback
to the driver if a problem exists with the signal bulb(s) for vehicles built with side
repeaters.
Models
IMPORTANT: Some of the involved vehicles may be in distributor/dealer
used vehicle inventory. Distributors/Dealers should complete this recall
service on these vehicles before retail delivery. Distributors/Dealers should also
perform this repair on vehicles in for service. Involved vehicles can be determined
by using the VIP inquiry process.
Subject
Safety Recall No. F33 - Directional Signal Bulb Function
The Front Control Module (FCM) on LX/LE models or Totally Integrated Power
Module (TIPM) on PT models must be reprogrammed.
No parts required to perform this service procedure.
The following Special Tools are required to perform this service procedure:
NPN Battery Charger
CH9401 StarSCAN® Tool
CH9404 StarSCAN® Vehicle Cable
CH9409 StarSCAN® Documentation Kit
CH9410 StarSCAN® Ethernet Cable, 3.7 m (12 ft.)
CH9412 StarSCAN® Software Update Device Kit
TechCONNECT PC or equivalent
Reprogram the FCM/TIPM Module
NOTE: Before performing this Repair Procedure, the operating software in
the StarSCAN®must be programmed with software release level 7.01 or
higher. The software release level is visible in the blue header at the top of
the StarSCAN® screen.
CAUTION: Follow the flash reprogramming procedure carefully on LX/LE
models. The FCM does not support abort/recovery. If an error occurs,
the FCM will require replacement.
Repair
Parts Information
Special Tools
Service Procedure
Safety Recall No. F33 - Directional Signal Bulb Function
NOTE: The StarSCAN®diagnostic scan tool fully supports Internet
connectivity. However, to take advantage of this feature you must first
configure the StarSCAN® for your dealership's network. Make sure the
StarSCAN® is configured to the dealership's network before proceeding.
For instruction on setting up your StarSCAN® for the dealer's network
refer to either: “DealerCONNECT > Service > StarSCAN and
StarMOBILE tools > Online Documentation”, or refer to the StarSCAN®
Quick Start Networking Guide. The StarSCAN® Quick Start Networking
Guide is also available on the www.dcctools.com website under the
"Download Center".
1. Install a battery charger and verify that the charging rate provides
approximately 13.2 - 13.8 volts. Set the battery charger to continuous charge.
Do not allow the charger to time out during the flash process. Remove the
charger from the battery when the flash process is complete.
2. Connect the CH9410 StarSCAN® ethernet cable to the StarSCAN® and the
dealer's network drop.
3. Connect the CH9404 StarSCAN® vehicle cable to the StarSCAN® and the
vehicle.
4. Power ON the StarSCAN®.
5. Select "ECU View".
6. Touch the screen to highlight the TIPM/CGW or Front Control/Central
Gateway in the list of modules.
7. Select "More Options".
8. Select "ECU Flash"
9. Record the part number at the top of the "Flash" screen for later reference.
10. Select "Browse for New File". Follow the on screen instructions.
11. Highlight the appropriate calibration then select "Download to Scantool"
12. Select "Close" after the download is complete, and then select "Back".
13. Highlight the listed calibration.
14. Select "Update Controller". Follow the on screen instructions.
15. When the update is complete, select "OK".
Service Procedure cont.
Safety Recall No. F33 - Directional Signal Bulb Function
16. Verify the part number at the top of the "Flash” screen has updated to the
new part number.
NOTE: Due to FCM/TIPM programming, a DTC may be set in other modules
(PCM, TCM, BCM, MIC, SKREEM, etc.) within the vehicle, if so
equipped. Some DTC's may cause the MIL to illuminate. From the
"Home" screen select "System View". Then select "All DTCs". Press
"Clear All Stored DTCs" if there are any DTCs shown on the list.
Claims for vehicles that have been serviced must be submitted on the
DealerCONNECT Claim Entry Screen located on the Service tab. Claims
submitted will be used by DaimlerChrysler to record recall service completions
and provide dealer payments.
Use the following labor operation number and time allowance:
Labor Operation Time
Number Allowance
Reprogram FCM - LX/LE (B) 18-F3-31-82 0.3 hours
Reprogram TIPM - PT (B) 18-F3-31-83 0.3 hours
NOTE: See the Warranty Administration Manual, Recall Claim Processing
Section, for complete recall claim processing instructions.
Regional offices will receive an electronic list of involved vehicles. The Vehicle
List is arranged by Distributor/Dealer code and in Vehicle Identification Number
(VIN) sequence. The lists are for Distributor/Dealer reference in arranging for
service of involved vehicles.
Service Procedure cont.
Completion Reporting and Reimbursement
Distributor/ Dealer Notification and Vehicle List
Safety Recall No. F33 - Directional Signal Bulb Function
All involved vehicle owners should be notified of the service requirement by their
Distributor/Dealer. Owners are requested to schedule appointments for this service.
A sample copy of the owner notification letter is attached.
All involved vehicles have been entered into the Global Recall System (GRS) and
Vehicle Information Plus (VIP) for Distributor/Dealer inquiry as needed.
GRS provides involved Distributors/Dealers with an updated VIN list of their
incomplete vehicles. Completed vehicles are removed from GRS within several
days of repair claim submission.
Distributors/Dealers must perform this repair on all unsold vehicles before
retail delivery. Distributors/Dealers should also use the VIN list to follow up with
all owners to schedule appointments for this repair.
If you have any questions or need assistance in completing this action, please
contact your International Service and Parts Manager.
International Service and Parts
DaimlerChrysler Corporation
Owner Notification and Service Scheduling
Vehicle Lists, Global Recall System, VIP and Distributor/Dealer Follow up
Additional Information
© Copyright 2006, DaimlerChrysler Corporation, All Rights Reserved
SAFETY RECALL - DIRECTIONAL SIGNAL BULB FUNCTION
Dear 300/Charger/Magnum/PT Cruiser Owner:
Customer satisfaction is very important to DaimlerChrysler. Accordingly, we are recommending
the following service on 2005 model 300/Magnum vehicles and some 2006
300/Magnum/Charger/PT Cruiser vehicles.
The problem is...
The driver’s “telltale” for directional signal bulb failure may not
provide feedback to the driver if a problem exists with the signal
bulb(s).
What your dealer
will do...
DaimlerChrysler will repair your vehicle free of charge (parts and
labor). To do this, your dealer will reprogram the Central Gateway
Module with new software. The work will take about ˝ hour to complete.
However, additional time may be necessary depending on how dealer
appointments are scheduled and processed.
What you must do...
If you need help...
Simply contact your dealer right away to schedule a service appointment.
If you have trouble getting your vehicle serviced, please contact the
DaimlerChrysler Distributor nearest your location. A representative will
assist you in getting your vehicle serviced. This information can be found
in the Customer Assistance section of your Owner's Manual.
If you have already experienced the problem described above and have paid to have it repaired,
contact the DaimlerChrysler Distributor nearest your location for reimbursement procedures.
We apologize for any inconvenience, but we are sincerely concerned about your
satisfaction with your DaimlerChrysler vehicle. Thank you for your attention to
this important matter.
International Service & Parts
DaimlerChrysler Corporation
Notification Code F33